Paintball Gun Air Reservoir

1. Field of invention

The present invention pertains to paintball guns and more particularly to a gas holding chamber for use with CO.sub.2, nitrogen or compressed air powered paintball guns that replaces an existing bolt.

2. Background

Today's high tech paintball guns generally run off of CO.sub.2, nitrogen or compressed air as a power source. These power sources require a specific volume of gas or a specific pressure of gas to fire the paintball at the correct velocity. You can use one or the other. Most paintball guns use the higher pressure/low volume method to shoot a paintball. Then, a few years ago, miniature pressure regulators became available for use on paintball guns allowing players to use a lower pressure gas to fire the paintball, thus relying on more volume of air to fire the paintball. But, the pressure never got below 500 psi into the air chamber of the paintball gun because valves at that time were not built for efficiency at lower pressures. At the same time paintball pressure regulators became available on the market, manufacturers and after-market customizers shortened the paintball guns to reduce weight by cutting off part of the air chamber, thus reducing the amount of stored gas. At that time there was no problem caused by reducing the length of the chamber because high pressure/low volume was being used. But as the newer, more gas efficient air valves that operate on a lower pressure/high volume (ranging from 100 psi to 400 psi) started to become available, the lack of air-chamber space has caused the paintball guns not to be able to shoot the paintball at the proper velocity using a lower pressure/high volume setting less than 500 psi.

What is needed is a reservoir chamber that bolts onto the the paintball gun through an existing bolt hole into the air chamber of the paintball gun thus increasing the chamber's volume capacity to allow paintball guns to use the more efficient low pressure/high volume air valves. The chamber should not significantly increase the weight or change the balance of the paintball gun and work without modifying the paintball gun by drilling out the air chambers. The air chamber needs to allow air to rush from the reservoir more rapidly through a straight-line passage to the valve; unlike the previous mounting bolt that allows air to enter the gun 90 degrees from the valve and pass through a small hole in the front mounting block bolt thus restricting air flow.

The present invention accomplishes these objectives by providing a reservoir that can thread into an existing bolt hole on the air chamber of the paintball gun, replacing the old bolt. The air reservoir has threads for the bolt hole, inlet holes to allow air into the air-chamber, a flange to hold an o-ring on the gun to seal air inside, a large chamber space to store a large volume of air, and a plug to seal the end of the chamber and to provide means of tightening the air reservoir to the gun.

FIG. 1 depicts a cross-section view showing the location of the chamber on the paintball gun and the previous mounting bolt and air inlet,

FIG. 2 depicts a cross-section view showing the location of the air chamber on the paintball gun and the air reservoir location in accordance with the present invention; and

FIG. 3 is a cross-section view of the air reservoir for more detailed inspection.

Referring now to FIGS. 1-3 of the accompanying drawings, the air reservoir chamber of the present invention will be described. FIG. 1 and 2 essentially shows where and how the air reservoir 8 is located in place of the previous bolt 4. The paintball gun body 1 is shown to show location of valve chamber 2 and the air chamber 3 and location of front mounting block 7 and the older design mounting block bolt 4. The front block mounting bolt 4 screws into paintball gun body 1 and has a small air transfer hole 5 to allow air to flow through from air inlet 6 to the air chamber 3. The air transfer hole 5 is small which restricts air flow and reduces performance, so people have to increase air flow through the bolt by drilling the holes larger. That works to increase flow rate but also reduces the strength of the bolt and still does not solve the problem of the reduced chamber space.

For a comparison, FIG. 2 shows the present invention, the air reservoir 8 mounted in the same location as the older front mounting block bolt 4 to pictorially show the increased size of the air chamber.

FIG. 3 shows a cross section view of our present invention, the air reservoir 8 where 9 indicates the threaded end that attaches to the paintball gun body 1 which is shown on FIGS. 1 and 2. A turned down diameter 15 which allows air to flow around the whole diameter and enter through multiple holes 10 and fill the air chamber 3 and the air reservoir chamber 12. A flange 11 has been turned on the air reservoir chamber 12. A flange 11 has been turned on the air reservoir to secure an o-ring 16 in place and seal air inside and apply pressure to keep the mounting block secured to the paintball gun body 1. The transfer tube 14 has been enlarged over that of the old mounting block bolt 4 which allows air to rush from the air chamber 12 in a straight line path to the air chamber 3 in less time and with less restriction than in previous designs referred to in FIG. 1. The air reservoir has a plug 13 to seal air inside the reservoir and provide the air reservoir with the means of being tightened down to the paintball gun body.