Polymers Which Form Liquid-Crystalline Phases

7 mg of a methyl hydrogenopolysiloxane of the formula ##STR20## and 99 mg of 2-undecenyloxy-3,6,7,10,11-penta-n-pentyloxytriphenylene, prepared as described in Example A.2), were dissolved in 2 ml of toluene, and 100 ppm, based on the solution, of hexachloroplatinic acid were added. The mixture was kept at 80.degree. C. for 2 days. The organopolysiloxans was purified by preparative gel permeation chromatography in tetrahydrofuran, and was dried under reduced pressure. The polymer chain contained on average 35 groups derived from the compound (A.2). The polymer had a glass transition temperature of about -29.degree. C., the discotic/isotropic transformation took place at +39.degree. C., and the heat of transformation was determined as 13 J/g.

Using a procedure similar to that described in Example 1, 17 mg of a copolysiloxane of the formula ##STR21## in which the Si(CH.sub.3).sub.2 O and SiHCH.sub.30 groups are randomly distributed and the mean value of n is 35, were reacted with 126 mg of 2-undecenyloxy-3,6,7,10,11-penta-n-pentyloxytriphenylene, prepared as described in (Example A.2). In the resulting polymer, an average of 35 groups derived from the compound (A.2) were bonded to the polymer chain. The polymer obtained had a discotic phase, which underwent a transition to an isotropic phase at 36.degree. C. The enthalpy of transformation was determined as 11.7 J/g, and the glass transition temperature was -29.degree. C.

4 g (6.9 millimoles) of 2,3,6,7,10,11-hexaacetoxytriphenylene XI (prepared according to O. C. Musgrave and C. J. Webster, J. Chem. Soc. C 1971, 1397), 8.1 g (58.5 millimoles) of finely powdered anhydrous potassium carbonate and 21.2 g (140 millimoles) of n-pentyl bromide in 80 ml of acetophenone were stirred under a nitrogen atmosphere for 16.5 hours at 116.degree. C. The cooled reaction mixture was filtered under suction through a G 3 frit, and the warm residue was extracted several times with a total of 250 ml of ether, until a sample of the residue was completely soluble in water. The filtrate and the ether extract were combined, washed with three times 100 ml of water saturated with CO.sub.2 and dried over anhydrous sodium sulfate, the ether was distilled off, and acetophenone and excess pentyl bromide were distilled off at below 50.degree. C. under reduced pressure from an oil pump.

The residue, which crystallized slowly, was taken up in 20 ml of acetic anhydride in order to acetylate any free OH groups present. Excess acetic anhydride was removed under reduced pressure, and the residue obtained consisted of 5 g of crude product containing 2,3,6,7,10,11-hexapentyloxytriphenylene, 2-monoacetoxy-3,6,7,10,11-pentapentyloxytriphenylene and diacetoxytetrapentyloxytriphenylene.

The crude product was separated into fractions by column chromatography over silica gel (500 g), using a 3:2 (v/v) methylene chloride/petroleum ether mixture; the middle fractions contained the desired compound 2-acetoxy-3,6,7,10,11-pentapentyloxytriphenylene.

The final fractions contained the diacetoxy compounds.

The products obtained after the fractions had been evaporated down were further purified by recrystallization from ethanol/diethyl ether or methanol.

2-Monoacetoxy-3,6,7,10,11-penta-n-pentyloxytriphenylene has a clear point of 161.degree. C. and does not crystallize above -50.degree. C.

Working up and purification were carried out by procedures similar to those described under (A.1).

599.7 mg (0.87 millimole) of 2,6-diacetoxy-3,7,10,11-tetra-n-pentyloxytriphenylene (which had been recrystallized from methanol) were mixed with 200.3 mg (0 87 millimole) of decane-1,10-dicarboxylic acid (recrystallized from 20% strength ethanol and then from 1:1 (v/v) ethanol/hexane). 1.5 mg (1 mole %) of p-toluenesulfonic acid were added as a catalyst. The mixture was heated to 130.degree. C. under a protective gas atmosphere, a melt being formed. This temperature was maintained for 2 hours, after which acetic acid was distilled off under 200 mbar for 1 hour, and the pressure was reduced to .about.20 mbar, depending on the evolution of gas bubbles. This procedure took 2 hours.

The mixture was then heated under reduced pressure from an oil pump (0.5-0.05 mbar), and the temperature had to be increased in intervals of 10.degree. C. in order to obtain an isotropic (clear) melt in each case. Finally, the melt was kept under <0.01 mbar and at 185.degree. C. for 3 hours. It was then cooled, and the resulting melt cake was dissolved in 7 ml of tetrahydrofuran and carefully precipitated in 120 ml of n-hexane. The precipitate was separated off by centrifuging and was digested with hexane, centrifuging was carried out once again, and the precipitate was once again taken up in 5 ml of tetrahydrofuran and again precipitated in 70 ml of hexane. The dry polymer no longer contained any residual starting material (thin-layer chromatography in CH.sub.2 Cl.sub.2 : Rf=0). The yield was 410 mg (59% of theory).

Phases according to DSC and polarization microscopy:

g 4020 C. D 194.degree. C. i

D=discotic phase g=columnar phase

i=isotropic phase.

Enthalpy of transition from D to i: 15 J/g

20 mg of the polymer obtained as described in Example 1 were dissolved in 1 ml of methylene chloride, and 1 mg of copper tetradecyloxyphthalocyanine of the formula (XIII) ##STR24## where T is --C.sub.10 H.sub.21, in the form of a 5% strength solution in tetrahydrofuran, was added. The solvent was evaporated off at room temperature, and the residue was then kept for 12 hours at room temperature under a pressure of 1 mbar. The colored polymer did not exhibit any change in the meso phase behavior.

The procedure described in Example 4 was followed, except that the compound XIII in which T is C.sub.12 H.sub.25 was used.

The resulting blue polymer exhibits phase behavior similar to that of the polymer of Example 1.